Lifco Hydraulics Mobile Logo


Single Vane Pumps T7DS Series

     Denison Vane Pumps are specially designed for high and low circuit applications and deliver wide speed ranges (600 to 3600 RPM) and high efficiencies of over 94% under high pressure. Search Lifco Hydraulics Single Vane pump stock below:




Unit#(Click item for more)DescriptionStockPrice(USD)
024-90158-0T7DS B28 2R00 A100Out Of StockPlease Contact Us
024-90881-0T7DS 045 2R00 A100Out Of StockPlease Contact Us
024-90747-0T7DS 045 1R00A1Out Of StockPlease Contact Us
024-92917-0/01T7DS 045 3R01 A100Out Of StockPlease Contact Us
024-90157-0T7DS B28 3L00 A100Out Of StockPlease Contact Us
024-76333-5T7DS B22 1R00 A5M0Out Of StockPlease Contact Us
024-90451-0T7DS B31 3R00 A100Out Of StockPlease Contact Us


Minimum Speed: (RPM) 600 600 600 600 600 600 600
Maximum Speed: (RPM) HF-3, HF-4, HF-5 1800 1800 1800 1800 1800 1800 1800
Mounting Standard: SAE J744, SAE B ISO 3019-2100 A2 HW SAE J744, SAE B ISO 3019-2125 A2 HW SAE J744, SAE C ISO 3019-2125 A2 HW SAE J744, SAE C
Weight: Lbs (without connector/bracket) 34.6 50.7 50.7 57.3 57.3 95.4 95.4
Moment of inertia: (Lb.in2) 2.6 1.1 1.1 6.7 6.7 21.3 21.3
Need Assistance?

024-90158-0 T7DS B28 2R00 A100

Amazon Link:
Price(USD):Please Contact Us
Stock:Out Of Stock

Common Units:

  • T7BS B04 3R00 A101 (024-58786-0)
  • T6CM B10 2R00 C1 (024-44870-0)
  • T7DS B42 2R02 A100 (024-91596-0/02)
  • T7ES 050 3R00 A100 (024-94562-0)

3-D Drawings:

T6E 3D Drawing
T6E_T7ES Shaft 1 SAE C
View PDF

Application: T7E Vane Pump

     How do you get a large hydraulic press to open quickly, smoothly and also efficiently? You provide it with a flow of oil that is increased from small to large and back to small again, ramp this flow quickly and provide it at a pressure no greater than required to accelerate the weight of the platen. This is done by using a “Drive Controlled Pump”. In one particular application, a Parker T7E-085 (16.4 cubic inch per revolution) vane pump, a 75 horsepower electric motor and an electric motor AC drive unit (frequency controller and regulation electronics) were used. No oil was forced over relief or throttle valves; thus, little energy was wasted! The electric motor was controlled by the AC drive unit to increase the speed of the pump drive (thus increasing its output flow) over a short period of time, getting the platen moving quickly and smoothly. At 1800 RPM this pump produces 125 GPM of fluid. Then, the AC drive unit was used to decrease the speed of the pump drive over a short period of time, bringing the platen to a stop. Thanks to the very wide range of speed (up to 3000 rpm) and the high operating pressures (up to 320 bar), the “Drive Controlled Pump” system solution can be tuned exactly to a customer's specific requirements. The robust double lip design makes the Parker vane pump impervious to particle contamination and maintains a high degree of efficiency in the long term. Also, the design of Parker’s vane pump, with its two opposing pressure chambers, prevents lateral forces working on the drive shaft, eliminating mechanical stress within the pump and providing a long reliable working life.